[Q30-Q52] Network Appliance NS0-593 Practice Verified Answers – Pass Your Exams For Sure! [2022] – IT Certification Exam Questions & Answers

Rate this post

Network Appliance NS0-593 Practice Verified Answers – Pass Your Exams For Sure! [2022]

Valid Way To Pass NetApp NCSE’s NS0-593 Exam

NetApp NS0-593 Exam Topics:

Section	Objectives
Protocols	– Demonstrate knowledge of ONTAP NAS configurations – Demonstrate knowledge of ONTAP SAN configurations – Demonstrate knowledge of S3 server configurations
Software-defined ONTAP Solutions	– Describe software-defined ONTAP solutions
Hardware	– Demonstrate knowledge of hardware troubleshooting – Demonstrate knowledge of troubleshooting SP or BMC – Describe the hardware components in a Fibre Channel environment – Demonstrate knowledge of the cluster interconnect infrastructure – Describe MetroCluster configurations

NetApp NS0-593 Exam Certification Details:

Exam Name	Support Engineer ONTAP Specialist
Exam Registration	PEARSON VUE
Number of Questions	60
Recommended Training	ONTAP Troubleshooting (ILT)
Duration	120 minutes

NO.30 You recently discovered the error message shown below in your ONTAP logs.

What should be your first action to correct this Issue?

Power cycle all the disk storage shelves that contain drives of the aggregate with the my_data_vol
volume.

Determine the root cause behind the inconsistency before attempting any recovery procedure.

Use the storage takeover command on the storage controller that contains my_data_vol.

Use the wafliron command against my_data_vol to solve the inconsistency on the volume.

NO.31 Your customer installed the shelf firmware for their NS224 shelf over a week ago, and the firmware has
notupgraded on shelf 1 module B. The customer wants to know what the next steps would be to get the
firmware upgraded after verifying that the shelf firmware is indeed loaded onto the system.
Which step would you perform to complete the firmware upgrade?

Reseat the NSM100 module.

Reseat the disk in Bay 0.

Power cycle the shelf.

Reseat the PSU of the shelf.

NO.32 A customer wants to connect a NetApp AFF A700 system to a 40GbE switch. The controllers have a 10/40G
Ethernet card in slot 4 for this purpose. The link comes up fine on node 2,but it will not come up on node 1.
You look at the AutoSupport data for the nodes in question and see the output shown in the exhibit.

What is the cause of the customer’s problem?

The cable is plugged in upside down.

The incorrect cable is used.

The ports are configured for 4x10Gbit instead of 40Gbit.

The port has an incorrect SFP inserted.

NO.33 After a motherboard replacement on a NetApp AFF A300 in a SAN environment, the customer states that
ports 0e and 0f are unable toconnect to the fabric. The ports report “offline”.
What would you examine first to troubleshoot the issue?

vserver fcp wwpn-alias show command output

system node hardware unified-connect show command output

storage port show command output

vserver fcp interface show command output

NO.34 Recently, a CIFS SVM was deployed and is working. The customer wants to use the Dynamic DNS(DDNS)
capability available in NetApp ONTAP to easily advertise both data UFs to their clients. Currently. DNS is
only responding with one data LIF. DDNS is enabled on the domain controllers.

Referring to the exhibit, which two actions should be performed to enable DDNS updates to work? (Choose
two.)

Disable the -vserver-fqdn parameter for the SVM DDNS services.

Remove the NFS protocol from the cifs_01 data LIF.

Enable the -use-secure parameter for the SVM DDNS services.

Enable the -is-enabledparameter for the SVM DDNS services

NO.35 A customer’s storage administrator Informs you about the deactivated Automatic Switchover (AUSO) feature
on their MetroCluster IP environment.
What Information would you tell your customer in this scenario?

The AUSO feature cannot be activated due to a non-mirrored aggregate.

The AUSO feature is not available in Metrocluster IP installations by design.

A faulty link automatically deactivated the AUSO feature.

This is a configuration failure, you can activate that feature for the customer.

NO.36 Your customer calls you because one application is not able to access a NetApp ONTAP S3 bucket. While
reviewing the EMS log on the cluster, you see the following message:

The same credentials work in another application.
In this scenario, what would cause this problem?

The application is trying to log in as an anonymous user.

The application is using v2 signatures.

The application is using v4 signatures.

The application is trying to access using the HTTP protocol.

NO.37 Your customer is running a NetApp AFF A800 system with NetAppONTAP 9.8 software and states that their
NS224 shelf is not showing with the correct shelf ID. You analyze the data and the shelf shows an
identification of “1.SHFHUXXXXXXXXXX.”
What is the cause of the reported Issue?

The shelf has been power cycled.

A new shelf was added to the controller.

The shelf had a disk replaced too quickly.

The shelf was cabled Incorrectly.

NO.38 You Just used the CLI to create a NetApp ONTAP FlexGroup Volume on a NetApp Cloud Volumes ONTAP
instance. After creation, you notice odd behavior in NetApp Cloud Manager.
In this scenario,what Is the reason for this behavior?

Cloud Volumes ONTAP does not support FlexGroup volumes.

The Capacity Management Mode within Cloud Manager should be set to Manual.

The Capacity Management Mode within Cloud Manager should be set to Automatic.

Cloud Manager must be used to provision the FlexGroup volume.

NO.39 A customer is calling you to troubleshoot why users are unable to connect to their CIFS SVM.

Referring to the Information shown in the exhibit, what Is the source of the problem?

Thev1db database is offline.

The aggregate aggr2 has a failed disk.

The databases On Node03 must be Switched from secondary to master.

The broken disk in Node03 is the source of the problem.

NO.40 Your customer noticed in NetApp Active IQ that their NetApp Cloud Volumes ONTAP forAzure HA solution
is no longer sending AutoSupport messages over HTTPS. A support ticket has been opened to find out why.
No changes have been made to the Cloud Volumes ONTAP for Azure HA environment.
In this scenario, which two autosupport command parameters should be used to validate that AutoSupport Is
working properly? {Choose two.)

-mail-hosts

-transport

-proxy-url

-to

NO.41 Your customer mentions that they have accidentally destroyed both rootaggregates in their two-node cluster.
In this scenario, what are two actions that must be performed? (Choose two.)

Rejoin the second node to the re-created cluster.

Re-create the cluster from the local backup.

Install ONTAP from a USB device.

Re-create the cluster from the remote backup.

NO.42 You notice poor performance on your FlexGroup and execute the system node run -node * flexgroup show
command for more Information. You notice the “Urge” column has non-zero values.
In this scenario, which statement is true?

The aggregate is completely full.

The constituent volumes are out ofInodes.

The data placement is uneven.

The constituent volumes are completely full.

NO.43 You have a 2-node NetApp FAS2750 switchless cluster with twenty-four 1.8 TB disks that is experiencing
performance issues. Upon investigation, you discover severaltype B consistency points.

Referring to the exhibit, which corrective action would address these consistency points?

Create additional data LIFs.

Convert the 2-node switchless cluster to a 2-node switched cluster.

Add an additional shelf oftwenty-four 1.8 TB disks.

Replace the twenty-four 1.8 TB disks with twelve 4 TB disks.

NO.44 You have a NetApp ONTAP cluster consisting of four NetApp FAS8200 controllers with two NetApp
CN1610 cluster switches running ONIAP 9.8 software. You are receiving several alert messages stating that
the cluster network has degraded. After troubleshooting, you determine that the errors are being generated
fromNode 2, interface e0b.
In this scenario, what should you do first to solve this problem?

Replace the Twinax cable between Node 2, Interface e0b. and the NetApp CN1610 switch.

Replace the motherboard on Node 2.

Replace both NetApp CN1610 switches.

Replace the NetApp CN1610 switch that connects to Node 2, interface e0b.

NO.45 After a normal power down of both nodes forbuilding maintenance, Node01 of a 2-node cluster cannot be
powered back up; however, all disk shelves are powered.
Which action should be performed to bring the cluster online and allow Node02 to serve data?

Recreate the cluster with the system configuration recovery cluster recreate -from node command.

Reboot the node With the system node reboot -node Node02 -bypass-optimization true command.

Perform a takeover with the storage failover takeover -ofnode Node01 -option forcecommand.

Reinitialize the cluster with option 4a from the boot menu.

NO.46 Your customer complains about missing volume snapshot copies on a SnapMlrror destination. While
investigating this case, you notice an executed SnapMirror resync operation in the event logs of the system.
In this scenario, what Is the cause of this problem?

Newer Snapshot copies than the common snapshot that was chosen for resync were removed
automatically at the destination.

The autodelete option removed Snapshot copies before the resync.

Snapshot copies were manually removed from the destination after the resync.

NetApp ON TAP System Manager removed these snapshot copies due to a snapshot schedule.

NO.47 You have a customer complaining of long build times from their NetApp ONTAP-based datastores. They
provided you packet traces from the controller and client. Analysis of these traces shows an average service
response time of 1 ms. QoS outputconfirms the same. The client traces are reporting an average of 15 ms in
the same time period.
In this situation, what would be your next step?

The cluster is responding slowly and requires further investigation using performance archives.

The client that reports high latency should be investigated.

The cluster interconnects should be investigated.

A sync core should be triggered.

NO.48 Your customer wants to access a LUN on a FAS 8300 system from a VMware ESXi server through the FC
protocol. They already created a new SVM, volume. LUN, and igroup for this purpose. The customer reports
that the server’s FC HBA port Is online, but the LUN does not show up.

Referring to the exhibit, what is the reason for this problem?

The FC service has not been configured on the SVM.

The zoning on the FC switches Is Incorrect.

The LUN Is not mapped to the correct SCSI ID.

The esxserver igroup contains incorrect IQNs.

NO.49 Your customer has mounted an NFS SVM from a Linux client unci performance is very poor. The customer is
certain that they have jumbo frames enabled. They have verified an MTU of 9000 on both the Linux client and
the broadcast domain on the NetApp ONTAP 9.8 cluster.

Referring to the exhibit, which ONTAP command will help isolate a possible MTU mismatch?

NO.50 An administrator receives the following error message:

What are two causes for this error? (Choose two.)

There Is excessive SSD load causing the wear leveling to become unbalanced.

A disk is falling.

There is excessive SATA HDD load.

An SSD disk is performing garbage collection to create a dense data layout.

NO.51 You have recently discovered that NetApp ONTAP Cloud Manager is not sending AutoSupport messages to
NetApp.
In this scenario, what would solve this Issue?

Verify that your AWScredentials are correctly added to Cloud Manager.

Verify that your NetApp Support site credentials are correctly added to Cloud Manager.

Verify that your data LIFs allow traffic to mysupport .netapp.com on port 443.

Verify that the inbound and outbound rules allow AutoSupport on port 80.

NO.52 You want to assign storage access to an NVMe protocol host.
Which three objects must beconfigured to accomplish this task? (Choose three.)

the NVMe subsystem

the NVMe broadcast domain

an NVMe LIF

the NVMe namespace

an NVMe LUN