[Q85-Q104] Tested Material Used To H31-341-ENU Test Engine Exam Questions in here [Oct-2022] – IT Certification Exam Questions & Answers

Rate this post

Tested Material Used To H31-341-ENU Test Engine Exam Questions in here [Oct-2022]

Penetration testers simulate H31-341-ENU exam PDF

What is the salary of Huawei H31-341 certified professional

Australia: $104,000
UK: $92,500
Singapore: $91,000
Spain: $79,500

QUESTION 85
Which of the following reasons may cause a business error? (Multiple choice)

The tail wire connector is seriously polluted

Dispersion compensation is unreasonable, such as under- or over-compensation

The temperature in the equipment room is too high

Transmitting laser performance degradation of the originating OTU board

The optical power of the incoming fiber is too high or too low

QUESTION 86
The ROADM site using WSMD9 board can support up to 9 dimensions. If it exceeds 9 dimensions, it can be implemented by cascading WSMD9 boards.

TRUE

FALSE

QUESTION 87
When creating a Client path using the path method, if the RL0S alarm is generated on the line card, the path cannot be created.

TRUE

FALSE

QUESTION 88
In the sub-(wave) characterization test, what kind of standard does the isolation test require?

<20dB

<25dB

>20dB

>25dB

QUESTION 89
When the board detects that the error rate of the regenerator section signal exceeds 10 by detecting the B1 byte, the B1_SD alarm is reported.

TRUE

FALSE

QUESTION 90
What common methods for MSTP device fault location can be summarized as?

One board change, two loopbacks, three analysis.

One analysis, two loopbacks, three board change.

One analysis, two board change, three loopbacks.

One loopbacks, two board change, three analysis.

QUESTION 91
Which of the following statements about avoiding the generation of discrete trails are correct?

Use the trail function for configuration.

For services configured on a per-NE basis, search for trails on the NMS to ensure that the service configurations are complete and standard.

A fiber cut or switching test must be performed on the trail with protection routes to ensure that the configuration is complete and standard.

Guide users to learn service configuration specifications.

QUESTION 92
The setting of alarm reversal is based on:

Veneer

Network element

Port

Alarm

QUESTION 93
The collection and storage of on-site data includes periodic collection during normal operation of the equipment and collection of equipment failures. Generally, before the fault is processed, the maintenance personnel must collect and save the field data.

TRUE

FALSE

QUESTION 94
Which of the following description of the principle of automatic protection switching of the standard SSM protocol is correct? (Multiple Choice)

The network element broadcasts the clock quality information of the synchronization source to the downlink site through the s1 byte. And reverse notice the uplink site by the S1 byte in the direction of the synchronization source that the clock quality from the local network element is “not available for synchronization”.

If there are multiple clock sources with the highest quality level, the network element selects the clock with the highest clock priority as the synchronization source.

According to the clock source priority table, the network element first selects the clock with the highest quality level from the available clock sources as the synchronization source.

The network element broadcasts the clock quality information and the clock source ID of the synchronization source to the downlink site through the S1 byte, and reverse notices the uplink site that the clock quality from the local network element is “not available for synchronization” by the S1 byte in the direction of the synchronization source.

QUESTION 95
Using the path method to create a Client path fails. What are the possible reasons? (Multiple choice)

FEC mode does not match at both ends of the transceiver

The channel has been used up

Physical connection lacking between boards

There is no complete OCh path

QUESTION 96
When the grooming service level of the line board is ODUflex, which of the following protection schemes can be supported?

ODUk SNCP

ODUk SPRing protection

SW SNCP

Tributary SNCP

QUESTION 97
A, C are the WDM OTM stations, and B is the relay station.
When the transmission direction of the A to B stations is interrupted, the Wavelength side of the B-stack OTU relay board reports the R_LOS emergency alarm and runs the processing to the upstream A.
The station side OTU2_BDI secondary alarm. At the same time, the alarm continues to be transmitted to the downstream station of the B station. After the alarm is processed at the C site, the ODU2_PM_AIS minor alarm is reported on the WDM side of the C-site OTU, and the ODU2_PM_BDI secondary alarm is transmitted back to the upstream station A.

TRUE

FALSE

QUESTION 98
When the working channel protected by the optical line fails, it cannot be automatically switched to the protection channel. What are the possible reasons? (Multiple Choice)

Protection group parameter configuration error

Artificially issued a lock command

Waiting for the recovery time to be set too long

The protection channel is faulty

QUESTION 99
Which of the following local maintenance terminals can be used to manage MSTP equipment?

U2000 LCT

U2000 Web LCT

U2000 IP LCT

All of the above

QUESTION 100
Which of the following is not an advantage of WDM?

Large capacity and transparent data transmission

Easy to upgrade and maximize protection of existing investments

Completely replace SDH equipment

Compatible with all optical switching networks in the future

QUESTION 101
Which of the following ROADM boards have WSS optical modules? (Multiple Choice)

WSMD9

WSD9

WSM9

RDU9

QUESTION 102
Which of the following IP addresses are not part of the private IP address?

172.128.0.1

10.255. 0.1

10.0.0.1

192.168.0.1

QUESTION 103
The following description of the Directioned scenario, which is correct? (Multiple choice)

The wavelength carrying the local service can be transmitted to fixed direction.

If the current path needs to be adjusted, you must inbound to adjust the fiber connection of the network.

Directioned scenes are applied to networks that are not ASON.

When the service needs to be adjusted, or the working path is faulty, the optical crossover can be manually configured to implement flexible scheduling of services.

QUESTION 104
In the WDM system, after a certain distance of transmission, the optical signal-to-noise ratio of the receiving signal will be reduced to a certain extent. What is the main reason?

Fiber attenuation is too large

Use of the splitter combiner

Use of EDFA

No new fiber is used

Loading …