100% Reliable FlashArray-Implementation-Specialist Exam Dumps Test Pdf Exam Material [Q21-Q37] – IT Certification Exam Questions & Answers

Rate this post

100% Reliable Microsoft FlashArray-Implementation-Specialist Exam Dumps Test Pdf Exam Material

Based on Official Syllabus Topics of Actual Pure Storage FlashArray-Implementation-Specialist Exam

Pure Storage FlashArray-Implementation-Specialist Exam Syllabus Topics:

Topic	Details
Topic 1	Installation: This section of the exam measures the skills of Enterprise Infrastructure Technicians and focuses on executing a successful installation of FlashArray systems. It tests the ability to perform physical setup, cabling, configuration of network settings, and the application of initial system configurations necessary for full deployment.
Topic 2	Post-Installation Upgrade: This section of the exam measures the skills of FlashArray Implementation Specialists and evaluates how professionals confirm system functionality after installation or an upgrade. It involves validating connectivity, running health checks, confirming configurations, and ensuring that the deployment meets operational expectations.
Topic 3	Upgrades: This section of the exam measures the skills of FlashArray Implementation Specialists and focuses on tasks involved in managing firmware and software upgrades. Candidates must demonstrate knowledge of upgrade planning, verification steps, and rollback procedures, ensuring that systems are updated with minimal disruption to service.
Topic 4	Pre-Installation Upgrade: This section of the exam measures the skills of Enterprise Infrastructure Technicians and covers all preparation activities before deploying or upgrading a Pure Storage FlashArray. It includes understanding environmental requirements, verifying prerequisites, checking compatibility, and validating system readiness through appropriate tools and documentation.

QUESTION 21
When accessing the FlashArray GUI, which management IP address is recommended for use?

CT1 management IP

CT0 management IP

Virtual management IP

QUESTION 22
After running puredb run giveback –safe command once CT0 has been upgraded, how long should the Implementation Engineer wait before continuing with the controller upgrade?

3 minutes

5 minutes

10 minutes

QUESTION 23
What is the required PSU wattage for a FlashArray// X70R2/R3 or X90R2/R3 array?

1200W

1300W

1600W

QUESTION 24
After an Implementation Engineer installs a new FlashArray and runs health checks, they see that Phonehome and Remote Assist are NOT working correctly. Which outbound port needs to be open for all management ports (physical and virtual)?

443

123

QUESTION 25
A customer wants to expand the capacity of their FlashArray//X10 from 5/5 to 11/11. Which is the correct action to take?

Evacuate and swap one pack at a time.

Perform a drive-by-drive swap of the modules.

Install a swing shelf with loan capacity to evacuate to.

QUESTION 26
After upgrading Purity during a new installation, which command should an Implementation Engineer run to determine what version of Purity will be loaded at the next boot of the FlashArray?

purearray list –controller

pureversion -a

pureboot list

QUESTION 27
A customer has scheduled the installation of a FlashArray//X70R4. Core services such as DNS, NTP and SMTP are currently unavailable due to a network outage, but the Implementation Engineer proceeds with the installation as planned. What should the Implementation Engineer expect during the installation?

Core service validation checks will fail during setup, but the installation can complete and services can be verified later once restored.

The array will automatically skip configuration of all network-dependent features and require a full reinitialization later.

Purity will set itself to NOT start on bootup due to services unable to be verified during installation.

QUESTION 28
Prior to running the puresetup command, which command should an Installation Engineer run on a new install of a FlashArray//XR4 array?

pureboot list

cobalt check . py

purehw list

QUESTION 29
What command should the Implementation Engineer run to configure a proxy?

puresetup proxy https://yourproxyserver:1234

purearray setattr –proxy https://yourproxyserver:1234

purearray configure –proxy url https://example.proxy.server

QUESTION 30
A customer would like to consolidate their SAS shelves and wants to evacuate multiple shelves in parallel. What is a prerequisite for this procedure?

Purity must be upgraded to 6.x

The array chassis must be fully populated with modules.

The array usage percentage must be lower than 60%

QUESTION 31
The Pure Engagement Request (PER) specifies that iSCSI ports ETH2 and ETH3 should be set to 10 Gb/s.
After configuring the ports and connecting them to the SAN, the Implementation Engineer observes that ETH2
/3 are not negotiating and display 0 b/s. The SAN is operating at 40 Gb/s, with support for up to 100 Gb/s.
What should the Implementation Engineer do to resolve this issue and complete the install?

Force negotiate the array iSCSI ports to 40 Gb/s.

Replace the transceivers with the appropriate type.

Force negotiate the switch iSCSI ports to 40 Gb/s.

QUESTION 32
On FlashArray models that use standard DFMs instead of DFMDs, which NVRAM bays are always populated?

NVB0 and NVB1

NVB0 and NVB2

NVB0 and NVB3

NVB1 and NVB2

QUESTION 33
After racking a new FlashArray with one data pack, how should DirectFlash modules be installed?

Starting in bay 19, right to left.

Starting in bay 0, left to right.

Starting in bay 10, left to right.

QUESTION 34
After completing an installation, the customer requests to configure replication IP settings. Where in the GUI does the customer need to navigate in order to do this?

Storage > Replication

Storage > Array Connections

Settings > Network

System > Configuration

QUESTION 35
During a hardware NDU from FlashArray//XR2 or XR3 to an XR4 model, which default service on-board ports are NO longer present in the XR4 controller design?

iSCSI

Replication

Management

QUESTION 36
Which FlashArray//XL DirectMemory Modules (DMMs) configuration condition is true?

DMMs are only compatible with //XL 170.

DMMs cannot be installed in a DirectFlash Shelf (DFS).

DMMs use different drive slots to regular DirectFlash modules.

QUESTION 37
An Implementation Engineer attempts to add a FlashArray to a Fusion fleet but receives an error indicating the array cannot be added. The array appears healthy and is connected to Pure1.
What is the most likely cause of this issue?

The array is already assigned to another Fusion fleet.

The array does NOT have any existing workloads configured.

The array is NOT running the latest Purity//FA version.

The array’s management interface is physically disconnected.