Start your NSE6_FSW-7.2 Exam Questions Preparation with Updated 57 Questions [Q33-Q56] – IT Certification Exam Questions & Answers

Rate this post

Start your NSE6_FSW-7.2 Exam Questions Preparation with Updated 57 Questions

A Fully Updated 2025 NSE6_FSW-7.2 Exam Dumps – PDF Questions and Testing Engine

Fortinet NSE6_FSW-7.2, also known as Fortinet NSE 6 – FortiSwitch 7.2 Certification Exam, is a certification program designed for network professionals who want to validate their skills and knowledge in configuring, managing, and troubleshooting FortiSwitch products. Fortinet NSE 6 – FortiSwitch 7.2 certification program is essential for individuals who want to specialize in Fortinet’s network security solutions and advance their careers in the field of cybersecurity.

NO.33 Exhibit.

port24 is the only uplink port connected to the network where access to FortiSwitch management services is possible. However, FortiSwitch is still not accessible on the management interface. Which two actions should you take to fix the issue and access FortiSwitch? (Choose two.)

You must add port24 native VLAN as an allowed VLAN on internal.

You must add VLAN ID 200 to the allowed VLANS on internal.

You must allow VLAN ID 4094 on port24, if management traffic is tagged.

You should use VLAN ID 4094 as the native VLAN on port24.

NO.34 Exhibit.

You need to manage three FortiSwitch devices using a FortiGate device. Two of the FortiSwitch devices initiated a reboot after the authorization process. However, the FortiSwitch device with the configuration shown in the exhibit. did not reboot All three devices completed FortiLink manage-ment authorization successfully.
Why did the FortiSwitch device shown in the exhibit not reboot to complete the authorization pro-cess?
The management mode was set to use FortiLink mode.

Switch auto-discovery is enabled.

The management mode was set to use FortiLink mode.

The FortiSwitch device is scheduled to reboot as part the authorization process

The system time is not in-sync and is using a non-default value

NO.35 Which two statements about VLAN assignments on FortiSwitch ports are true? (Choose two.)

Configure a native VLAN on the FortiLink

Assign an IP address and subnet mask to FortiSwitch VLANs

Only assign one native VLAN on a port

Assign untagged VLANs using FortiGate CLI

NO.36 Exhibit.

The exhibit shows the current status of the ports on the managed FortiSwitch.
Access-1.
Why would FortiGate display a serial number in the Native VLAN column associated with the port23 entry?

Port23 is a member of a trunk that uses the Access-1 FortiSwitch senal number as the name of the trunk.

Port23 is configured as the dedicated management interface.

A standalone switch with the showm serial number is connected on por123.

Ports connect to adjacent FortiSwitch devices will show their.serial number as the na-tive VLAN

NO.37 Refer to the exhibits.

Port1 and port2 are the only ports configured with the same native VLAN 10.
What are two reasons that can trigger port1 to shut down? (Choose two.)

port1 was shut down by loop guard protection.

STP triggered a loop and applied loop guard protection on port1.

An endpoint sent a BPDU on port1 that it received from another interface.

Loop guard frame sourced from port 1 was received on port 1.

NO.38 Which LLDP-MED Type-Length-Values does FortiSwitch collect from endpoints to track network devices and determine their characteristics?

Network policy

Power management

Location

Inventory management

NO.39 Which statement about 802.1X security profiles using MAC-based authentication mode is true?

FortiSwitch allows connectivity to all hosts connected to a port, if one host is authenticated.

FortiSwitch can grant each device a different access level based on the credentials provided

FortiSwitch performs faster when using this security mode on the ports.

FortiSwitch must communicate with the RADIUS server to authenticate devices

NO.40 Which is a requirement to enable SNMP v2c on a managed FortiSwitch?

Create an SNMP user to use for authentication and encryption.

Specify an SNMP host to send traps to.

Enable an SNMP v3 to handle traps messages with SNMP hosts.

Configure SNMP agent and communities.

NO.41 Which statement about the quarantine VLAN on FortiSwitch is true?

Quarantine VLAN has no DHCP server

Users who fail 802.1X authentication can be placed on the quarantine VLAN.

It is only used for quarantined devices if global setting is set to quarantine by VLAN.

FortiSwitch can block devices without configuring quarantine VLAN to be part of the allowed VLANs.

NO.42 How does FortiSwitch perform actions on ingress and egress traffic using the access control list (ACL)?

Only high-end FortiSwitch models support ACL.

ACL can be used only at the prelookup stage in the traffic processing pipeline.

Classifiers enable matching traffic based only on the VLAN ID.

FortiSwitch checks ACL policies only from top to bottom.

NO.43 Refer to the exhibits

Traffic arriving on port2 on FortiSwitch is tagged with VLAN ID 10 and destined for PC1 connected on port1. PC1 expects to receive traffic untagged from port1 on FortiSwitch.
Which two configurations can you perform on FortiSwitch to ensure PC1 receives untagged traffic on port1? (Choose two.)

Add the MAC address of PCI as a member of VLAN 10.

Add VLAN ID 10 as a member of the untagged VLANs on port1.

Remove VLAN 10 from the allowed VLANs and add it to untagged VLANs on port1.

Enable Private VLAN on VLAN 10 and add VLAN 20 as an isolated VLAN.

NO.44 Which feature should you enable to reduce the number or unwanted IGMP reports processed by the IGMP querier?

Enable the IGMP flood setting on the static port for all multicast groups.

Enable the IGMP flood reports setting on the mRouter port.

Enable IGMP snooping proxy.

Enable IGMP flood unknown multicast traffic on the global setting.

NO.45 What is the role of a device that is simultaneously functioning as both the distribution and core in the hierarchy network model?

POE with high density FortiSwitch

FortiGate managing FortiSwitch

FortiSwitch functioning as standalone

HA backup FortiGate managing FortiSwitch

NO.46 Which drop policy mode, if assigned to a congested port, will drop incoming packets until there is no congestion on the egress port?

Tail-drop mode

Weighted round robin mode.

Random early detection mode

Strict mode

NO.47 Which two statements about the FortiLink authorization process are true? (Choose two.)

The administrator must manually pre-authorize FortiGate on FortiSwitch by adding the FortiGate serial number.

FortiSwitch requires a reboot to complete the authorization process.

A FortiLink frame is sent by FortiGate to FortiSwitch to complete the authorization.

FortiLink authorization sets the FortiSwitch management mode to FortiLink.

NO.48 Which two statements about VLAN assignments on FortiSwitch ports are true? (Choose two.)

Configure a native VLAN on the FortiLink

Assign an IP address and subnet mask to FortiSwitch VLANs

Only assign one native VLAN on a port

Assign untagged VLANs using FortiGate CLI

NO.49 Exhibit.

LAG and MCLAG are used to increase the available network bandwidth and enable redundancy. How does spanning tree protocol see MCLAG and LAG if they are configured based on the physi-cal view shown in the exhibit? (Choose two)

Switch 1. Switch 2, and Switch 3 are seen as one MCLAG peer group

Switch 3 and Switch 4 uplinks are treated as single interfaces.

Switch 3 and switch 4 are seen as one MCLAG switch client

Switch 1 and Switch 2 both seen as one single switch.

NO.50 Refer to the diagnostic output:

Two entries in the exhibit show that the same MAC address has been used in two different VLANs. Which MAC address is shown in the above output?

It is a MAC address of FortiLink interface on FortiGate.

It is a MAC address of a switch that accepts multiple VLANs.

It is a MAC address of an upstream FortiSwitch.

It is a MAC address of FortiGate in HA configuration.

NO.51 Refer to the exhibits.

Port1 and port2 are the only ports configured with the same native VLAN 10.
What are two reasons that can trigger port1 to shut down? (Choose two.)

port1 was shut down by loop guard protection.

STP triggered a loop and applied loop guard protection on port1.

An endpoint sent a BPDU on port1 that it received from another interface.

Loop guard frame sourced from port 1 was received on port 1.

NO.52 Which two types of Layer 3 interfaces can participate in dynamic routing on FortiSwitch? (Choose two.)

Detected management interfaces

Loopback interfaces

Switch virtual interfaces

Physical interfaces

NO.53 Exhibit.

What conditions does a FortiSwitch need to have to successfully configure the options shown in the exhibit above? (Choose two.)

The FortiSwitch model is equipped with a maximum of 54 interfaces.

The CLI commands are enabling a splitpo rt into four 10Gbps interfaces.

The port full speed prior the split was 100G SFP+

The split port can be assigned to native VLAN

NO.54 Which two statements about DHCP snooping enabled on a FortiSwitch VLAN are true? (Choose two.)

Enabling DHCP snooping on a FortiSwitch VLAN ensures requests and replies are seen by all DHCP servers.

switch-controller-dhcp-snooping-verify-mac verifies the destination MAC address to protect against DHCP exhaustion attacks.

By default, all FortiSwitch ports are set to forward client DHCP requests to untrusted ports.

Settings related to DHCP option 82 are only configurable through the CLI

NO.55 Refer to the exhibit.

Core-1 and Access-1 are managed and authorized by FortiGate-1. which uses port4 as the FortiLink interface. After FortiGate authorizes and manages Core-2. Port1 status becomes STP discarding.
Why is port1 in the discarding state?

port1 on Core-2 is discarding only management traffic.

Core-1 and Core-2 do not have MCLAG configuration.

Access-1 is the root bridge and can only have one root port.

Core-2 has the lowest bridge priority.

NO.56 What type of multimode transceiver can be used to split a 40G port?

QSFP+ transceiver

SFP transceiver

QSFP transceiver

SFP+ transceiver

The Fortinet NSE 6 – FortiSwitch 7.2 certification exam covers a wide range of topics, including FortiSwitch hardware and software architecture, VLAN configuration, Spanning Tree Protocol (STP), link aggregation, and multicast routing. Candidates will also be tested on their ability to configure FortiSwitch security features, such as access control policies, port security, and network segmentation. NSE6_FSW-7.2 exam consists of multiple-choice questions and simulations, and passing the exam requires a deep understanding of FortiSwitch technologies and their practical applications in real-world scenarios.

Easy Success Fortinet NSE6_FSW-7.2 Exam in First Try: https://www.it-tests.com/NSE6_FSW-7.2.html