NS0-093 PDF Dumps Mar 22, 2025 Exam Questions – Valid NS0-093 Dumps [Q37-Q59] – IT Certification Exam Questions & Answers

Rate this post

NS0-093 PDF Dumps Mar 22, 2025 Exam Questions – Valid NS0-093 Dumps

Ultimate NS0-093 Guide to Prepare Free Latest Network Appliance Practice Tests Dumps

Network Appliance NS0-093 Certification Exam is designed to validate the skills and knowledge of hardware support engineers who work with NetApp storage systems. NetApp Accredited Hardware Support Engineer certification exam is intended for individuals who have the expertise to support and troubleshoot NetApp storage systems in a variety of environments. NS0-093 exam covers a range of topics, including hardware components and configurations, installation and setup, maintenance and troubleshooting, and system performance and optimization.

NEW QUESTION 37
A node has panicked with a PCI/NMI error. Giveback has not been performed.
Which two commands should you run to collect the logs to determine the cause? (Choose two.)

pelog -a -g=2

show pci -v

rdfile /mroot/etc/log/SSRAM

event log show

NEW QUESTION 38
You have replaced a failed boot device. You perform boot_recovery and receive no errors. However, when the node reboots, it reports that it has no disks.
What are two possible causes? (Choose two.)

The SAS cables were incorrectly reconnected after reinstalling the motherboard.

The disks that are owned by this node have been marked as failed.

The node is booting a lower version of ONTAP software than was last used.

The interconnect is down.

NEW QUESTION 39
In preparation for an upgrade to ONTAP 9.6P8 software, you have uploaded the ONTAP image
96P8_q_nodar_image.tgz onto your local web server with address 192.168.10.10.
Which is correct command syntax to download this image to the cluster image repository?

ClusterA::> storage firmware download -node local -package-url
http://192.168.10.10/96P8_q_nodar_image.tgz

SP ClusterA-01> cluster image package get -url
http://192.168.10.10/96P8_q_nodar_image.tgz

ClusterA::> cluster image package get -url
http://192.168.10.10/96P8_q_nodar_image.tgz

ClusterA::> cluster image package get -url
http://netapp.com/ontap9/downloads/96P8_q_nodar_image.tgz

NEW QUESTION 40
Where is a kernel core file stored on a FAS9000 system that is running ONTAP 9.12.1 software?

on the partner root aggregate

on the root aggregate

on the mailbox disk

on the boot device

NEW QUESTION 41
You are replacing a boot device on a FAS8300 system that is running ONTAP 9.10P6 software. You attach a USB memory stick to the external USB port on the storage controller but cannot access the memory stick.
What step needs to be performed to access the boot device?

Set the port to “enabled” with setenv.

You need to use ONTAP 9.11 or later software.

Add the boot device before the BIOS is loaded.

The external USB port is not activated on NetApp systems.

NEW QUESTION 42
You have upgraded your cluster from ONTAP 9.5 software to ONTAP 9.7 software. After two days, you notice that the upgrade is causing issues. You decide to revert to ONTAP 9.5 software.
Which two actions do you need to complete before you revert? (Choose two.)

Revert from ONTAP 9.7 software to ONTAP 9.6 software and then to ONTAP 9.5 software.

Delete all Snapshot copies from the past two days.

Reinstall your boot media and install ONTAP 9.5 software.

Wipe your config and restore from backup.

NEW QUESTION 43
In the latest MANAGEMENT LOG AutoSupport message, you try to inspect the ENVIRONMENT section but find it empty.
In which section of AutoSupport can you find the reason?

AUTOSUPPORT-BUDGET.XML

HEADERS

AUTOSUPPORT-HISTORY.XML

MANIFEST.XML

NEW QUESTION 44
Which command can you use to confirm successful completion of an ONTAP upgrade?

system controller sp upgrade show

cluster image show-update-progress

job show -jobtype upgrade

system node upgrade-revert upgrade-task -node <nodename> -version <ontap Version>

NEW QUESTION 45
During which two operations is the NVRAM replayed by the high-availability (HA) partner? (Choose two.)

after triggering a sync core

when a node is halted

during a negotiated takeover

when the node loses power

NEW QUESTION 46
Which two ONTAP systems support both SSD and SAS disks? (Choose two.)

AFF C190

FAS2750

AFF A220

FAS8200

NEW QUESTION 47
Which two of the following are field replaceable units (FRUs) on an AFF A220 system? (Choose two.)

NVMEM battery

mSATA boot device

NVME Flash Cache feature

chassis fan

NEW QUESTION 48
In which two sections of AutoSupport can you find information to analyze the following panic? (Choose two.) Panic_Message: PCI Error NMI from device(s):ErrSrcID(CorrSrc(0xf00),UCorrSrc(0x18)), RPT(0,3,0):
Qlogic FC 16G adapter in slot 1 on Controller

HA-RASTRACE.TGZ

ALL-COREDUMP.XML

SSRAM-LOG

PCI-HIERARCHY.XML

To analyze the provided panic error, the two sections of AutoSupport that are essential for investigation are:
* What it is:HA-RASTRACE.TGZ contains HA (High Availability) system trace logs. It records hardware diagnostics, error traces, and the HA system’s response to hardware events. These logs are critical when analyzing hardware-related panics, including those caused by PCI errors.
* Why it’s relevant to the panic:In the given panic message, the NMI (Non-Maskable Interrupt) error originates from a Qlogic FC 16G adapter. HA-RASTRACE.TGZ will provide detailed diagnostics, including the error reporting from the HA interconnect and other hardware diagnostics. Specifically, it may include information about how the system detected the PCI fault and any actions taken to protect the system state.
* How to analyze:
* Extract the HA-RASTRACE.TGZ file from the AutoSupport bundle.
* Review hardware-related trace messages for entries associated with the PCI bus or the Qlogic FC adapter.
* Look for specific error codes or keywords like PCI Error, NMI, or Qlogic.
* References:
* NetApp’s “AutoSupport Logs and Diagnostics Guide” highlights HA-RASTRACE.TGZ as a primary resource for debugging hardware faults.
* The “Panic Troubleshooting Guide” for ONTAP systems specifies HA-RASTRACE as a key source for identifying NMI-related errors.
1. HA-RASTRACE.TGZ
* What it is:SSRAM-LOG records low-level hardware error details, including PCI device register states and uncorrectable memory errors. It is particularly useful for analyzing errors originating in peripheral hardware like network or storage adapters connected via PCI.
* Why it’s relevant to the panic:The panic message explicitly references a PCI Error NMI caused by a Qlogic FC adapter. SSRAM-LOG captures detailed state information for PCI devices, which can help identify whether the fault originated in the adapter hardware, the PCI bus, or another related component.
* How to analyze:
* Extract the SSRAM-LOG from the AutoSupport bundle.
* Search for PCI-related errors, including the specific error source IDs (e.g., ErrSrcID(CorrSrc (0xf00),UCorrSrc(0x18))).
* Review the log entries to confirm the root cause of the NMI.
* References:
* The “Hardware Diagnostics and Troubleshooting Guide for ONTAP” lists SSRAM-LOG as a key file for debugging PCI errors.
* NetApp’s documentation on PCI diagnostics emphasizes the use of SSRAM-LOG for validating hardware-level faults.
2. SSRAM-LOG

NEW QUESTION 49
What are the two steps to unfail a disk in maintenance mode? (Choose two.)

Reseat the disk.

Remove it from the Failed Disk Registry.

Use the “disk unfair command.

Use the disk remove command.

NEW QUESTION 50
Which two commands from the Service Processor can provide information about installed field replaceable units (FRUs)? (Choose two.)

system fru list

system fru show

system sensors show

system power status

NEW QUESTION 51
You are reviewing the output of disk show and one of the disks is reporting a container type of “unknown”.
What is causing this status?

The disk is not owned by a member of the high-availability (HA) pair.

The disk is failed.

The disk is in the maintenance center.

The disk does not have an owner.

NEW QUESTION 52
What are two options to remove Failure Byte on disks that are marked as failed? (Choose two.)

Power cycle the disk shelf.

Reseat the disk.

Update the disk firmware.

Unfail the disk

NEW QUESTION 53
You are using wafliron on an aggregate named homedir on a production system.
When is the data on homedir available?

when the administrator manually onlines the aggregate

when wafliron is started

after Phase 4 of wafliron is complete

after the mounting phase of wafliron is complete

NEW QUESTION 54
You have upgraded your cluster from ONTAP 9.5 software to ONTAP 9.7 software. After the upgrade, you notice that the upgrade causes issues. You decide to revert to ONTAP 9.5 software.
Which revert step is allowed?

Revert to ONTAP 9.5 software with the netboot procedure.

Revert from ONTAP 9.7 software to ONTAP 9.5 software by using the boot backup procedure.

Revert directly from ONTAP 9.7 software to ONTAP 9.5 software.

Revert from ONTAP 9.7 software to ONTAP 8.6 software and then to ONTAP 9.5 software.

NEW QUESTION 55
Your customer notices that their AFF A220 high-availability (HA) system is showing Single-Path HA.

How do you make the system into multipath HA?

0a and 0b on both controllers should be connected.

0a and 0c on both controllers should be connected.

0c and 0d on both controllers should be connected.

0a and 0d on both controllers should be connected

NEW QUESTION 56
At what stage is a write acknowledged to a client?

when the write is present in the local node RAM and NVRAM

when the write has been flushed to disk

when the write is present in the NVRAM on the local node and its HA partner

when the write has been flushed from NVRAM to RAM

NEW QUESTION 57
What is the default amount of time that a volume is available for recovery from the volume recovery queue following a volume deletion?

12 hours

48 hours

72 hours

24 hours

NEW QUESTION 58
When you plan an ONTAP upgrade, which NetApp tool generates a detailed upgrade plan?

ONTAP System Manager

Active IQ Unified Manager

Upgrade Advisor

Active IQ Config Avisor

NEW QUESTION 59
In a SAS stack of shelves, what is the topology of the connection between expander and disk?

arbritrated loop

point-to-point

loop

ring

Network Appliance NS0-093 exam is a certification exam aimed at hardware support engineers who work with NetApp products. NetApp Accredited Hardware Support Engineer certification is offered by NetApp, a leading provider of storage and data management solutions. NS0-093 exam is designed to test the skills and knowledge of hardware support engineers who work with NetApp products and technologies.

Passing Key To Getting NS0-093 Certified Exam Engine PDF: https://www.it-tests.com/NS0-093.html